Crimpers

For use on smaller motorcycle/automotive terminals including:
- HE050-series, Sumitomo
- HX040.JC-series, Sumitomo
- ICM22-series
- MLC070-series, Mini Multi-lock, Tyco/AMP
- W025-series, Sumitomo

NOT compatible with:
- JWPF-series, JST
- SS10-series, Tyco/AMP
- MX23A-series, JAE
- MX47-series, JAE

For use on most motorcycle/automotive terminals including:
- MTW-series, Hitachi
- MT, HM, HW-series, Sumitomo
- HX, DL, SL, TL, TS-series, Sumitomo
- DL, HX, TS 187 Sealed series, SUMI.187, Sumitomo
- HD, HE 187 Unsealed series, SUMI.187U.A, Sumitomo
- DL, TS 187 Unsealed series, SUMI.187U.B, Sumitomo
- RFW-series, Furukawa
- 250-series, Sumitomo
- 312-series
- BC35, BC40-series bullet connectors
- CN(A), Yazaki
- LB-series
- HX040, HV/HVG-series, Sumitomo
- DC090-series, Sumitomo
- SSD-series, Yazaki
- SSC-series, Tyco/AMP Sealed Sensor Connector
- 090 and 090II-series, Yazaki
- QLW-series, Furukawa
- YESC.15, 1.5mm System Sealed, Yazaki

NOT compatible with:
- MP150-series, Metri-Pack 150 Rear Insert type, Delphi
- MP150U-series, Metri-Pack 150 Unsealed, Delphi
- GT150.35- and GT150.45-series, GT-150 Sealed, Delphi
- MP150.2-series, Metri-Pack 150.2 Pull to seat, Delphi
- MP150P-series, Metri-Pack 150 Pull to seat, Delphi
- WP-series, Weather-Pack, Delphi
- SS10-series, Tyco/AMP Superseal 1.0
- SS15-series, Tyco/AMP Superseal 1.5
- ESJ-series, Tyco/AMP Econoseal MkII J-series
- ES3-series, Tyco/AMP Econoseal III
- JPT-series, Tyco/AMP Junior Power Timer
- KOM1-series, Bosch Kompakt

For use on red, blue, yellow insulated terminals
AWG 10-12, 14-16, 18-20 Nylon & Vinyl

"W" crimp for use on uninsulated terminals
22-16, 16-14, 12-10, 8 AWG size Tyco/AMP SOLISTRAND terminals and splices

• Ratcheting design ensures consistent quality crimps
• Adjustable crimp pressure
• Thumbscrews to interchange dies
• Size: 8.7"

• Angled head design
• Ratcheting design ensures consistent quality crimps
• Adjustable crimp pressure
• Thumbscrews to interchange dies
• Size: 9.3"

Molded case holds either our Standard crimp frame or Pro-Crimp frame, and five die sets (including one in frame)

• Length: 255mm/10.04in
• Width: 150mm/5.90in (closed)
• Height: 45mm/1.77in

An economical crimper with 5 cavities to crimp open barrel terminals from 24-14 AWG. Parallel jaw action helps prevent the rolling tendency of ratcheting type crimpers, but require greater hand force to operate, so these are recommended only for occasional use. 8.4" length.
Comparable to Delphi 12085271 and SPX Kent-Moore J-38125-7 crimpers

For use with a wide variety of open barrel crimp terminals including:
- MTW-series, Hitachi
- MT, HM, HW-series, Sumitomo
- DS, HD, HM, MT 090 Unsealed, Sumitomo
- HX, DL, SL, TL, TS-series, Sumitomo
- RFW-series, Furukawa
- HE050-series, Sumitomo
- ICM22-series
- KOM1-series, Bosch Kompakt
- W025-series, Sumitomo
- LB-series
- HX040, HV/HVG-series, Sumitomo
- HX040.JC-series, Sumitomo
- DC090-series, Sumitomo
- SSD-series, Yazaki
- SSC-series, Tyco/AMP Sealed Sensor Connector
- SS15-series, Tyco/AMP Superseal 1.5
- ES3-series, Tyco/AMP Econoseal III
- JPT-series, Tyco/AMP Junior Power Timer
- 090 and 090II-series, Yazaki
- GT150.35- and GT150.45-series, GT-150 Sealed, Delphi
- MP150.2-series, Metri-Pack 150.2 Pull to seat, Delphi
- MP150P-series, Metri-Pack 150 Pull to seat, Delphi
- MP150U-series, Metri-Pack 150 Unsealed, Delphi
- YESC.15, 1.5mm System Sealed, Yazaki

NOT compatible with:
- 250-series
- BC35, BC40-series bullet connectors
- QLW-series, Furukawa
- ESJ-series, Tyco/AMP Econoseal MkII J-series
- MP150-series, Metri-Pack 150 Rear Insert type, Delphi
- MX23A-series, JAE
- MX47-series, JAE
- JWPF-series, JST
- SS10-series, Tyco/AMP Superseal 1.0
- WP-series, Weather-Pack, Delphi

An economical crimper for Delphi GT, Metri-Pack, and Weather-Pack terminals from 22-14 AWG. Parallel jaw action helps prevent the rolling tendency of ratcheting type crimpers, but require greater hand force to operate, so these are recommended only for occasional use. 8.4" length.

For use with Delphi open barrel crimp terminals including:
- MP150-series, Metri-Pack 150 Rear Insert type, Delphi
- GT150.35- and GT150.45-series, GT-150 Sealed, Delphi
- MP150.2-series, Metri-Pack 150.2 Pull to seat, Delphi
- MP150P-series, Metri-Pack 150 Pull to seat, Delphi
- MP150U-series, Metri-Pack 150 Unsealed, Delphi
- MP280, Metri-Pack 280, Delphi
- WP-series, Weather-Pack, Delphi

Crimps Deutsch closed barrel (screw machine) 20-12 AWG terminals.

• Economical crimper delivers the same type of crimp the more expensive MIL-Spec tools provide.
• Built-in locator assures accurate positioning of the pin and socket.
• Full cycle ratchet insures a complete and perfect crimp each and every time.
• Cushioned grips. Compact 6.5" size.

Molex brand "F" type crimper, for Molex .093", .062", Mini-Fit, KK, SL, etc., that is well suited for a wide range of other terminal types as well, for 24-14 AWG wire.
Features 13 "F" crimp cavities from 1.4-4.8mm (1.4, 1.6, 1.8, 2.0, 2.3, 2.5, 2.8, 3.2, 3.4, 3.6, 3.9, 4.3, 4.8mm)
Molex P/N: 63811-1000

NOT compatible with:
- GT150.35- and GT150.45-series, GT-150 Sealed, Delphi
- HX040.JC-series, Sumitomo
- MP150-series, Metri-Pack 150 Rear Insert type, Delphi
- MP150U-series, Metri-Pack 150 Unsealed, Delphi
- MP280, Metri-Pack 280, Delphi
- MX23A-series, JAE
- MX47-series, JAE
- QLW-series, Furukawa
- SS10-series, Tyco/AMP Superseal 1.0
- WP-series, Weather-Pack, Delphi

Ideal for crimping small terminals, the Hozan P-706 is machined and built to high standards that result in a high quality crimp.

Features 11 "F" crimp cavities from 1.4-3.7mm (1.4, 1.7L, 1.7H, 2.0L, 2.0H, 2.4L, 2.4M, 2.4H, 2.8, 3.2, 3.7mm)
L=Narrow crimp width, M=Mid size crimp width, H=Wide crimp width (Widest, of the particular size available)
3 round insulation crimps: 1.8, 2.5, and 4.0mm diameter
Made in Japan

Suitable for:
- 090II-series, Yazaki
- 58X-series, Yazaki
- 250-series (250.TL, 250.ATL), Sumitomo/Yazaki
- ESJ-series, Tyco/AMP Econoseal MkII J-series
- MT, HM, HW Sealed series, Sumitomo
- HX, DL, SL, TL, TS-series, Sumitomo
- GT150.45-series, GT-150 Sealed, Delphi
- HE050-series, Sumitomo
- HX040-series, Sumitomo
- HX040.JC-series, Sumitomo
- JPT-series, Tyco/AMP Junior Power Timer
- JWPF-series, JST
- KOM1-series, Bosch Kompakt
- MLC040, MLC040HL, MLC070-series, Mini Multi-lock, Tyco/AMP
- MX150-series, Molex
- SS10-series, Tyco/AMP Superseal 1.0
- SS15-series, Tyco/AMP Superseal 1.5
- SSD-series, Yazaki
- RFW-series, Furukawa

NOT compatible with:
- YESC.15, 1.5mm System Sealed, Yazaki
- GT150.35, GT-150 Sealed, Delphi
- DS, HD, HM, MT 090 Unsealed, Sumitomo
- MP150-series, Metri-Pack 150 Rear Insert type, Delphi
- MP150.2-series, Metri-Pack 150.2 Pull to seat, Delphi
- MP150P-series, Metri-Pack 150 Pull to seat, Delphi
- MP150U-series, Metri-Pack 150 Unsealed, Delphi
- MX23A-series, JAE
- MX34-series, JAE
- MX47-series, JAE
- SSC-series, Tyco/AMP Sealed Sensor Connector
- TS025-series, Sumitomo
- W025-series, Sumitomo

The Hozan P-707 features 13 "F" crimp cavities suitable for a wide range of terminals, both small and large.
Die range: 1.2-4.2mm (1.2, 1.4, 1.4L, 1.7, 1.7L, 2.0, 2.0L, 2.4, 2.4L, 2.9, 2.9L, 3.5, 4.2mm)
L=Narrow crimp width
2 round insulation crimps: 1.6, and 2.2mm diameter
Made in Japan

Suitable for (additional terminals still being evaluated):
- 250-series (250.TL, 250.ATL, but not 250.TL-SKT2), Sumitomo/Yazaki
- MX23A-series, JAE
- MX34-series, JAE
- MX47-series, JAE
- TS025-series, Sumitomo
- W025-series, Sumitomo

NOT compatible with:
- 58X-series, Yazaki
- MX150-series, Molex
- SSC-series, Tyco/AMP Sealed Sensor Connector